Hello first time grower here. I am growing 2 strains, hash plant and bubba kush, growing in pro mix under led lights, 2 wide spectrum led by phlizonthey say 1500 watt but there no where near that. Plants are in there 3 week of flower and all look good except a problem with the kush. Leaves are curling down ward and also curling inward lengthwise , I’m thinking over watering there watered twice a week but all plants go fairly dry between watering except s bubbas. Any help advice would really help alot.thanks in advance
2 Likes
Need a regular light pic cant tell colors well in that blurple.
Looks like tips burnt “nute burn” and potentially nitrogen claw
Are you still feeding high nitrogen nutes? What’s ppm going in?
Ppm in was 1050 feeding a full line of nutes called innovative plant solutions. These plants have always been slow and have had issues with watering(not all the plants fault being my first grow I’m making some mistakes). I will get some pics under normal light and post them.
2 Likes
I’m suspicious of true color if it’s dark green I would look into your nutes nitrogen lvl and potentially change nutes for flower to something low nitrogen. I would definitely reduce ppm into the 800-850 range and see if that stops the tip burn going forward.
In flower nitrogen needs of the plant are reduced from what it was during veg. If you give too much nitrogen the first change is deep deep green leaves that will curl or “claw” downward and taco upwards. This can be recovered from by changing your nutes to lower the amount of nitrogen you put in.
Thanks very much and your right the plants are dark green . Feed day saturday and I will pull it back to 800 ppm or so. And again thank you
1 Like
Anytime
The clawing of the leaves downward could be a sign of wind burn. Do you have a strong fan blowing onto the top of the plant?
I would also like to know temp and humidity levels
1 Like
Temp is pretty steady around 76 degrees and humidity 46%. I do have a fan going but it isnt directly on the plant.
I do have a fan going but it’s not directly on the plant.
1 Like
Temp and humidity sounds ok
Fill this out best you can
COPY/PASTE the below list into your forum post.
Answer these simple questions the best you can.
If you do not know, or do not use something; Just say so; Or post
NA (non applicable)
- What strain, Seed bank, or bag seed
- Method: Soil w/salt, Organic soil, Hydroponics, Aquaponics, KNF
- Vessels: Pots, Grow beds, Buckets, Troths
- PH of Water, Solution, runoff (if Applicable)
- PPM/TDS or EC of nutrient solution if applicable
- Indoor or Outdoor
- Light system
- Temps; Day, Night
- Humidity; Day, Night
- Ventilation system; Yes, No, Size
- AC, Humidifier, De-humidifier,
- Co2; Yes, No
Always try to upload a clear picture of any issues you may have to allow the community to assist you.
Add anything else you feel would help us give you a most informed answer should be included. Feel free to elaborate, but short and to the point questions and facts will help us help you in a more efficient manner 
Thanks!
1 Like
Well you’ve lost me on the copy and paste stuff I’m an old school guy not computer savy at all.
1 Like
No worries, brother! Just try to answer the questions in that list as best you can. We’re shooting in the dark without knowing more about your setup. By the way, welcome to ILGM! 
1 Like
Thanks bro
1 Like
Strain: Bubba Kush soil: pro mix vessels: 5gal cloth bags ph: 6.3 ppm in on last feed 1010
indoor: 5x5 grow tent lights: 2 phlizon 1500 wide spectrum led. Temps: day 75-79 night 65- 69 ventilation system: 250 cm exhaust fan with 16inch carbon filter. Also 250 cm fan with 16 inch
carbon filtered input. Humidity: day 45% to 50%. Night time 65% TO 70% Dehumidifier: yes on 24/7 c02: not at this time.
I’m not super familiar with Promix, but I think you want your pH a little lower than what’s typical in soil, closer to 5.8 as in hydro, around 6.0. Don’t quote me on that, but that could be part of the problem. The clawing looks like Nitrogen toxicity to me. Maybe you fed a little more because they were acting hungry because of lockouts? Hopefully someone with more experience can help out. I can’t think of anyone using Promix off the top of my head. @blackthumbbetty maybe?