Had 3 days where humidity hit around 70% . My dehumidifier had taken a dump on me. 1st time grower so im not sure what im looking at
Pics arent great but the second one the bud looks almost grey and dingy.
Pics arent great but the second one the bud looks almost grey and dingy.
3 Likes
I am not seeing anything to be concerned with. A few days of 70% rh this early in flower should not normally cause mold. Mold more often shows up late flower when buds are large and dense which limits air circulation through them.
6 Likes
From what I can tell, it’s just your healthy girl in early flower, with sparkly trichomes busting out. 
4 Likes
I hope your right. The second pic i had the flash on. Up close it looks blackish and dingy. The other plant only a few buds were orangish color.
2 Likes
I zoomed in the second pic, but still couldn’t see anything bad.
2 Likes
Thank you so much for responding. Got a new dehumidifier as soon as i could. Hope all goes well.
1 Like
Thank you brother 
. Much appreciated. This site really is the best community. Hope when im more advanced i can pay it back.
2 Likes
Your lookin ok to me! You might increase your air movement to help with the lack of the dehuey
3 Likes
You’re good , I see no signs of any mold or mildew.
2 Likes
Just noticed a few leaves on a Haze plant looking like this. Is this a calcium problem?
Its with 3 other strains in the same tent that look fine.
Completing the support ticket will help.
I think the questions about the medium, nutrients and ph/ppm are the most helpful
COPY/PASTE the below list into your forum post.
Answer these simple questions the best you can.
If you do not know, or do not use something; Just say so; Or post
NA (not applicable)
• What strain, Seed bank, or bag seed (photo or auto)
• Age of plant
• Method: Soil w/salt, Organic soil, Hydroponics, Aquaponics, KNF
• Vessels: Type and capacity of container (fabric, plastic, etc)
• PH and TDS (PPM or EC) of:
• Water,
• Solution,
• runoff (if Applicable)
• PPM/TDS or EC of nutrient solution if applicable
• Method used to measure PH and TDS
• Indoor or Outdoor if indoor, size of grow space
• Light system List brand and wattage/spectrum
• Actual wattage draw of lights
• Current Light Schedule
• Temps; Day, Night
• Humidity; Day, Night
• Ventilation system; Yes, No, Size
• AC, Humidifier, De-humidifier,
• Co2; Yes, No
If growing Hydro some additional questions:
-DWC? RDWC? Autopots? Ebb and Flow? Other?
-Distance of liquid below net pot (DWC)
-Temperature of reservoir
-TDS of nutrient solution
-Amount of air to solution
Always try to upload a clear picture in white light of any issues you may have to allow the community to assist you.
1 Like
Thank you. Will do
It looks pretty normal. What happens a lot of times with outdoor grows is it gonna throw you off for instance because of our chili temperatures in New York State right now? I have a few strands that are turning dark, blue and purple and they’re not even supposed to do that. Very interesting…
1 Like
Im not growing out doors. Not really sure what you’re responding to. Mold question or leaf discoloration? I should have made them 2 separate querys
1 Like
The little round rusty spots on plants leafs. If not already I would start using cal-mag on water day. Watch the new growth for improvement. Just my thoughts good luck.
2 Likes
Thank you so much. I appreciate your input. Im new and dont measure runoff and all that stuff. Just came so far dont wanna screw it up the last month.
2 Likes
You’re very welcome .
1 Like
As @kellydans said… another faster way is to mix cal-mag at 5ml/gallon and apply with a sprayer right before lights out. Tops and undersides of the leaves
2 Likes