Got the qb boards and went to HD and got my wiring and breakers for the sub panel, so I’ll build the lights and run my 20amp sockets tomorrow.
1 Like
I had my slurricane seed in water for 4 days before she cracked open. Set the cup on something warm like a router or cable box
1 Like
It’s been 24hrs only 2 have sunk to the bottom but all of them have tails and there all floating still, Going to take them out and put in wet paper towel in zip lock bag.
1 Like
Damn the router is on fire, really hot. Did I burn up my seeds. Paper towels still wet, I think I put to much water, I used 2 paper towels and soaked them , didn’t ring it out, I
have about 7 that are 1/4”, 3 that are 1/8”, 2 that are 1/16” if that.
Should I transplant the 1/4” ones into the solo cup
1 Like
Well I got 3 seedlings of the 12 
so I tried the remaining 3 seeds, all 3 sank to the bottom and then put in paper towel, after 24hrs all 3 had 1/2”t to 3/4” tap root. So I placed into solo cup last night. There 6 days behind the the other 3. Looks like they’ll make it
Ran 12/3 wire from the sub panel and placed outlet next to tent, I cut the bus bar on the side of the outlet so each receptacle has 20amps.
Will build my qb132 lights tomorrow.
Questions I can’t seems to find.
Soil in solo cup- how much water do you use to Presoak them
Do you pack the soil in or just scoop up the soil with the cup?
1 Like
Dont soak them. The seeds dont really need water in the ground right now, they need water from the air. So just plant them and put a dome over them
1 Like
Wanted to upload a pic. This ones been like this for about 24hrs, kinda droopy, any help would be appreciated.
Second Plant is still raising up but is a little yellow on the tip.
3rd is a runt
1 Like
They look pretty good, to me! Do they have domes over them? The one with the curling up margins is screaming for moisture.
1 Like
Yes I have clear solo cups That I cut the top 1.5 inch off so it slide right into the soil.
I spray the domes twice a day and give them a little fresh breath before I put it back on.
I’m not sure what a margin is I’ll look it up. Is that the 1st picture
1 Like
Couldn’t figure out why my rh was so low, I got the evdc300 by varnado. 3 days on high and continues and hasn’t even gone through 1 gallon. Opened it up and the damn wick filter is dry as a bone. It wasn’t even touching the water, I had to push it down.
1 Like
I was talking about the jagged edge of the leaf. The way those points are curling up means they are ‘thirsty’ so to speak, trying to catch some rain. If you got your humidifier working, that should help. 
1 Like
More pics
Everyone loves pics
3 WW planted on 11/12
1 BBG planted on 11-16
1 Ak47 planted 11-16
Any body know whats going on with this one
1 Like
I’ve been adding tribus, the recommenced dose was 1ml to 1gallon but said use with in 24 hrs. Ive only giving them 5ml of water a day
So I’ve been giving them 3 drops ea tribus with a squirt of 5ml of water. Not sure how to use the tribus. We’ll see how it works out.
So this is called the cotyledon, if it’s turning yellow then that means it’s getting ready to fall off, do I wait until it falls off to switch from 24/0 light to 18/6 light
I would only add the tribus to your feed like once a week.
1 Like
I don’t know if I’m doing this right. Do my plants look good?
they don’t look like other pics that are at the same stage as mine, there looking flat
- WW BBG Ak47
- Jiffy seed starter mix
- solo cup
- Reverse osmosis
- 8x4x8 tent
- T5 HO 6500k 8 bulbs
- Temps; 69-72
- Humidity; 50-60
- exhaust ac infinity T6, intake open flaps at the bottom of tent
- evdc300 Humidifier on high continuous
My light is a t5 HO with eight 6500k bulds.
Had it at 4” above canopy(just moved to 6”)
Doing 24hr light
5ml of water a day
Spraying dome every 12hrs
4 Likes
Looks great overall. I never put to much worry into seedlings looking funky. As long as they’re growing your good. You may want to raise the light up a few more inches to encourage a little more stretch. But overall, looking nice man.
4 Likes
Can I get a little help on hooking up my qb132 boards @dbrn32
Description and pics, thank you
Board are wired
Board 1 pos to brown driver
Board 1 neg to board 2 pos
Board 2 neg to board 3 pos
Board 3 neg to board 4 pos
Board 4 neg to blue driver
Input wiring
Driver->Plug
brown->Black
Blue->White
Green->Green
Output wiring
Driver->Board
Brown->white
Blue->black
1 Like