Converting Refrigerator to Growbox

I already posted much of this in my Grow Journal, but I thought I’d add this over here to see if I can get some more feedback and advice about this build.

My fiancee and I are just getting started with growing our own marijuana and our primary concern was concealment of our grow space. Sure we’d like high yields, however we don’t see the point if it’s going to jeopardize our jobs. So I recalled an article I’d read in High Times maybe 15 years ago or so about a grow box that was concealed inside an old refrigerator. With that in mind, we proceeded.

We started with an old GE refrigerator that we picked up off of Craigslist. A little bit of hunting and calling and we found one that was priced correctly: free. As we were going to be gutting it, we didn’t care if it worked or not so it wasn’t all that hard to find one. We pulled all the external components off and then gutted the interior of everything. I was hoping to get a fridge that had wire racks so we could repurpose them as grow shelves or light harnesses, etc. No such luck, our shelves were all glass and very dirty/scratched. Out they went. One thing to note is that there was still freon in the lines, so be careful to drain the tank before tearing everything out and make sure you’re able to ventilate your work area.

Once we had it stripped to a bare box, I used my Dremel tool with the standard cutting attachment to slice out the horizontal wall separating the lower refrigerator from the upper freezer. We had initially planned on installing lights, fans, humidifiers, etc up there and piping everything to the lower grow chamber, but I quickly decided that the bottom was way too small for our purposes. One or two cuts and I was able to pop that wall right out with no damage to any other surfaces. Then I cut off the plastic shelves that were attached to the doors. They extend 4-6" off the doors and were attached underneath the magnetic seal around the edge of the door. Rather than try to disassemble the door and risk compromising the seal, I was able to quickly cut them all off though there was a significant amount of white plastic shavings all over the garage floor. We then scrubbed the interior thoroughly to make sure we had a sterile environment before continuing.

Reading the forums here, we learned that in such a small space ventilation and heat would be our biggest challenge. We stopped by our local hydroponics supply store and picked up a 4" inline fan and a carbon filter to eventual use. We were able to expand a high hole on the back wall where water for the ice maker was pumped in. We ran a duct down the back of the fridge and down the now empty negative space where the motor and freon tank had previously been. We were able to secure the fan to the surface with the included hardware and some 90 degree brackets I had laying around. I decided not to securely mount the filter as we would obviously need to be able to clean and replace it from time to time, so I ran a couple of screws into the surface and found a way to mount the filter using picture-hanging wire and duct tape to create a good seal with the fan. I’m a bit concerned about the efficiency of this system as the ducting is long with several turns and the fan is pulling air, rather than pushing it. Additionally, I have no idea how effective the filter will be in this configuration, but the manufacturer assured us that it would do the job no matter which direction you routed the air flow. For the intake, I used a 1.5" spadebit to drill a couple of holes in the slanted wall on the floor of the fridge.

We opted for an LED bank of lights, Kind K3-L450. It was easily the most expensive part, but we wanted to reduce the amount of heat the lights added to our box and reduce future power costs. The included attachment didn’t offer any ability to raise or lower the lights, so I quickly decided I wanted to create a pulley system later on. We initially screwed some hooks into the ceiling to mount it, but the plastic shell is only a few millimeters thick and the interior insulation isn’t very dense, so we were’t satisfied that the hooks were very secure.

To mount the pulleys, I drilled some .25" holes into the ceiling and drove some eyebolts through them. A wide washer and nut were attached to secure the bolts, and then I took my Dremel metal cutting disc and lopped off the remaining bolt to keep the hardware as flush with the fridge as possible

The pulleys weren’t exactly cheap and I had to do a little bit of google-fu to figure out how to route the nylon string, but I outsmarted it and am happy with the results. I screwed a tie-down to the wall and now we can raise and lower the light with ease. It has a tendency to get lopsided, but the nylon string is limber enough that we can level the light bank very easily.

Rather than allow the sloping wall on the floor to eliminate a third of my space, I also installed a cheap wire rack I picked up at Target for a couple of bucks. It’s pretty sturdy, at least enough to hold a humidifier, air pump and clip fan…

With all that done, the last thing to worry about was snoopers. Obviously disguised as a refrigerator, no one is likely to think twice about it. But idle curiosity being what it is, we wanted to be able to keep idle hands from taking a peek. I installed some gate shackles to the door and exterior wall and now we can lock it up when there’s a chance of someone snooping.

The final product:

With the clip fan to encourage air movement and the fan running on medium, the fridge sounds pretty normal… maybe a bit loud, but nothing alarming or weird. We’ve been holding steady between 72-78F but humidity was so low it wasn’t even registering. I picked up a $10 portable humidifier from the drug store and now we’re keeping it solidly at 30-40%, not ideal but better than bone dry. Once we have larger plants and hydro tanks inside, I believe it will go up a bit more. We’ve opted for a couple of GH’s 4120 kits because they’re fairly easy.

We just germinated a couple of seeds and are getting going now. We’re planning on a ScroG grow. I’m going to install some screw hooks along the wall about a foot or so higher than the top of the hydro tanks and hang some thin 2" chicken wire. The wire should be light enough that when we need to change the water or clean the tanks, we can unhook the wire from the hooks and (hopefully) just hang it off the plants.

Anyway, that’s it. Any thoughts for improvement?


Good Job and I hope your work pays off…Keep us up on things.

You sir are a genius :slight_smile:

I was just walking by my basement beer fridge the other day thinking what a great grow box it would make. I was thinking you could use the upper freezer part for seedlings and clones and the bottom for growing.

Great job on your build. I might have to check out my local Craigslist to see if anybody is getting rid of an old fridge :slight_smile:

1 Like

I appreciate the kind words. So far so good. I’m including a link to my grow journal for those interested in how this system is working out.


I appreciate it! I found that a lot of the people “selling” fridges on craigslist were only asking for money to see if they could get anything for it. The one I actually got was posted as non-working and for sale for $50. I called and asked some questions and then said that $50 was too much and that I’d think about it. A day later, she called me back and said if I would just haul it away I could have it. Just something to think about when you’re looking around.

Also for seedling, cloning, and vegging, I’ve been thinking about converting a chest freezer. And then using this box for flowering only.


Nice Grow “Box” in the truest sense !!!

1 Like

Man you did a great job engineering that old fridge , awesome job buddy . Hell I might need to pull this off and it’s almost the perfect way to keep your grow hidden , wow that’s phenomenal !!!

1 Like

Had some issues with heat when I switched to the LED light bank, 450W. Temps spiked to 85F before I decided I needed to redesign the rig. I pulled the ducting off and installed rigid turns and pipes. Then I cut a larger intake into the slanted wall on the floor. It’s now about 6 inches wide. Also upgraded the humidifier and fan to an oscillating one. Things are much more stable now and temps are holding between 74-78F.


Even more heat issues for anyone who might want to replicate this system. I had set up my exhaust fan on the same timer with my lights and adjusted the fan down to medium-low. Temps were solid at 77-78F during the day, cooled to around 65F at night with only the humidifier and fan running. When everything cycled back on, the exhaust being set that low didn’t give it enough power to pull the quickly heated up air out… Temps spiked to 122F within the first two hours of day!!! Luckily, the plants didn’t react too negatively before I caught it. All is well…

So be aware, you can reduce the exhaust power during the day when the environment has stabilized, however be sure to reset it to a higher power before the system cycles on.


Upgraded to an ultrasonic humidifier over an evaporative humidifier. Humidity is up to a stable 52%. Plants were transplanted to DWC last week and started on nutes.


Looks great I have that same single bucket set up , keep us updated .

1 Like

System left locked and unattended for 48 hours while we took off for the weekend. Huge success! We came back to a box at 74F, 38%RH. Exhaust left on high, humidifier on low. Both of the girls are vegging nicely.

1 Like

Man they look like they doing good , gotta figure out my bucket , and the hydro growing so I can see what my results could be if I get thru a whole grow .

Just a little plant porn…

Super Silverhaze:

White Widow:


Here’s a look at how the canopy is developing.


Made a rig to keep the screen attached to the tanks, so it would be easier to change out the water


well done sir. well done indeed. more please.

Started flowering cycle last night. Screen is now about 80% full and the plants are drinking about a gallon a day…

1 Like

I’m gone need help to run my general water farm bucket ?

I’m a virtual novice to gardening and hydroponics, so I thought I was going to have all kinds of problems with this system. Nope, none. All of my challenges have come because of my choice to grow inside a refrigerator. I recommend the Waterfarm for beginners to hydroponics. For experienced growers like you, I think it will come easily.