Blurple conversion

I get it man, take your time. I’m in no rush.

I think QB boards are an option. I’ll just have to made some mods to the case.

So here’s what I’m wondering what I could power

Individual LEDs From Rapid LED. if so, how many?

LED strips?

Quantum boards, which ones? If I need to drop a different heat sink in it, that’s ok.

I think cobs would be too hot and require a pin heatsink that wouldn’t fit in the case. Correct?

Remember, I want this to looks like a Yugo and Preform like a Chevelle

So you want a sleeper? lol

Yeah… I was even thinking of a hinge to be able to see what’s under the hood.

Just waiting to hear what my drivers are capable of

You’re going to be limited to what you can use by operating voltage range of the drivers. All 3 are 60-85v and 820ma?

The only single modules I know of in that range are bridgelux vero 29c and cxb-3590 is available in 72v format. Both are cobs and would require some sort of heatsink material at that current. Probably not pin sinks unless you got rid of fans.

We can likely come up with a combination of strips to load driver within range, but you don’t have much real estate to mount them. Trying to figure out what will work and make sense, and having a difficult time.

What’s a good website for heat sinks?

I’d really like to get some UV out of this. Is that possible?

Ok… here’s what I can do. Gut the inside. Remove everything.

Get a heat sink, install it. This frame has three “bays” for lighting. The center bay, i’d like to use for a variety of UV lights and other “bloom” spectrum lights. On the left and right bay, one COB each.

I would take the fans out and mount them to the top of the box, blowing in, to cool the heat sink and driver. If I have to buy a better fan(s) so be it.

I’ll find out how they’re powered and use existing power if I can.

Can I get a driver that would power two cobs and a number of individual LED’s?

You can get just about anything. How much UV do you want and at what wavelength(s)?

Is the white unit the power supply for fans?

You tell me. It’s going to go into a 3x3 to help flower when needed. I’ll have a RSpec 260 kit in there as well.

I’m open to suggestions as to the wavelength(s) and how much is needed.

And I won’t need a dimmable driver.

I’d like to run the two cobs on a circuit and the UV and whatever else on a separate circuit to be controlled by the bloom switch, just for the novelty of it

If it has to be ran on a single circuit, that’s ok too. It’ll just be on the bloom switch.

Got me really. I’ve never been a proponent of UV. Pretty sure leds on fixture I’m using are still considered violet. Most of the people looking for uv want uvb. Cutter sells them in a strip or in a couple of small star configurations, I think they are $27 individually. I think the recommended current is pretty low too, so they would probably need their own driver anyway. I can read specs on them, but may be best to get with Mark at cutter if you want to go that route. 360-400nm are more readily available and probably more like working with any other led, and much cheaper.

If you get a piece of heatsink extrusion to fit, you could certainly open up to using cobs. There are some smaller models that you could run 2 per driver and end up with 6 cobs total. Probably still have room for fans on the drivers too.

Can I run 6 of these LEDs and 2 of these COBs on the same Meanwell Driver?

You could assuming driver fitting necessary specs exists. Did you determine current you would like to run? The low maximum current of the monos probably justifies going with cheaper cobs

I’m illiterate when it comes to LED lighting.

When you say current, I think of AC or DC. If that’s what you’re asking me, I don’t know what the difference would be.

The extent of my electrical training, 20 years ago, would be wiring air conditioners and thermostats.

Sorry if I’m making this difficult.

No worries. I’m asking about how many amps or milliamps. The cobs you listed have maximum current of 3600ma, and the monos maximum current is 1000ma. So if you put them on the same circuit you will have to build tending to the lower of the two.

If you that, you can use $10 cob instead of $30 cob without giving up too much.

Ok. I’m in. Would it be just one cob for each little driver?

I just want this to produce usable light for flowering. I’ve had some grandiose ideas for it, but I’ll settle for running cobs off each driver.

Just let me know what cobs to buy.

If you reuse drivers would have to be at least 2 36v cobs per driver.

Sounds good. I just ordered 12x7 heatsink.

Sweet! So we’re currently looking at doing 6 cobs and some 840nm monos? Do you have any preference on using something like bridgelux vero 18 or citi clu-048-1212 for the cobs? Both should be available at relatively low price, will just be a matter of what cct and cri we can find in stock. The vero 18 may be available in se model that comes with cob holder, but citizen would need purchased separately.

Is this the one?

Looks right. Those will have a butt load of different cct available. You said that you’re wanting more of a flowering light right? Take a look at some of the high cri options